Chain length for a 460 mm chainstay with a 36t ring and 40t sprocket
| Links (round up to even) | 114links |
|---|---|
| Length1,428 mm | 56.2in |
| FormulaPark Tool / Shimano method | 2 × 18.11 + 36/4 + 40/4 + 1 |
| Chainstay18.11″ — bottom bracket centre to rear axle | 460mm |
| Absolute minimumbig ring to big sprocket, with no slack left at all | 112links |
| From a 116-link chainlinks to take out of a new chain | remove 2 |
| Total teeth36t ring + 40t sprocket | 76 |
Notes
- Round up to an even number, always. A link is one inner plate plus one outer plate; there is no such thing as an odd link on a derailleur chain. 112.4 rounds to 114.
- Too long beats too short, and it is not close. A chain that cannot reach big ring to big sprocket will tear the derailleur into the wheel and take the hanger — sometimes the frame — with it. A chain a couple of links too long just hangs slightly slack in the small–small combination you should not be using anyway.
- Measure the chainstay to the axle centre, not to the dropout face. On a bike with sliding dropouts or an eccentric bottom bracket, measure it in the position you actually ride.
- This formula gives a slightly longer chain than wrapping it around the big ring and big sprocket and adding two links. That is deliberate: the wrap method has no allowance for the derailleur cage taking up slack, and it comes out short on long-cage rear derailleurs.
- A new chain on a worn cassette will skip under load. If you are replacing a chain that has been on the bike a long time, check cassette wear at the same time — a chain checker under 0.75% means you probably got away with it.
The formula
L = 2C + (F/4) + (R/4) + 1
with C the chainstay in inches, F the largest chainring and R the largest sprocket. For a 460 mm (18.11″) chainstay with a 36t ring and 40t sprocket that gives 56.2″ — 114 links.
Round up, and round to even
A link is one inner plate plus one outer plate. There is no such thing as an odd link on a derailleur chain, so the answer always lands on an even number. From a new 116-link chain, take out 2 links.
Too long beats too short, and it is not close
The absolute floor here is 112 links — big ring to big sprocket with no slack whatsoever. A chain that cannot reach that combination will pull the derailleur into the wheel and take the hanger, sometimes the frame, with it.
A chain a couple of links longer than ideal just hangs slightly slack in the small–small combination you should not be riding anyway.
Measure to the axle centre
Not to the dropout face. On a bike with sliding dropouts or an eccentric bottom bracket, measure in the position you actually ride.
Why this comes out longer than wrapping
Wrapping the chain around the big ring and big sprocket and adding two links has no allowance for the derailleur cage taking up slack, and it comes out short on long-cage rear derailleurs. That is the failure mode this formula is built to avoid.
Nearby sizes
- Chain length for a 455 mm chainstay with a 36t ring and 40t sprocket
- Chain length for a 450 mm chainstay with a 36t ring and 40t sprocket
- Chain length for a 460 mm chainstay with a 34t ring and 40t sprocket
- Chain length for a 460 mm chainstay with a 38t ring and 40t sprocket
- Chain length for a 460 mm chainstay with a 32t ring and 40t sprocket
- Chain length for a 460 mm chainstay with a 40t ring and 40t sprocket
- Chain length for a 460 mm chainstay with a 36t ring and 36t sprocket
- Chain length for a 460 mm chainstay with a 36t ring and 42t sprocket
- Chain length for a 460 mm chainstay with a 36t ring and 32t sprocket
- Chain length for a 460 mm chainstay with a 36t ring and 46t sprocket
Read more
- Sizing a Chain — Big-Big Plus Two, and When That Rule FailsA chain two links too long shifts badly and slaps. Two links too short destroys a derailleur the first time someone cross-chains by accident.
- Disc Pads and Rotors — The Numbers That Say ReplaceA pad worn to the backing plate gouges the rotor in one descent, and a rotor is several times the price of a set of pads.
- Hub Bearings — Play, Drag, and the Difference Between ThemTwo seconds with the wheel in the frame tells you whether a hub needs attention. Most people never do it, and hubs fail quietly.
- Gear Inches and Development — Two Ways to Compare Any Two BikesA 34/28 on one bike and a 30/25 on another are almost the same gear. Ratios alone will not tell you that; gear inches will.